Jump to content


Valued Contributors
  • Posts

  • Joined

  • Last visited

Everything posted by MDX-400

  1. Hi all, been a very long time since I've been on these forums! MD of course is just a faded memory by now and Sony otherwise seems to have gone downhill other than SCE--Playstation division. I'm sure not many frequent these forums any longer (Agoraquest has also become a dead zone) but I've made a couple interesting Sony "kijiji purchases" in the past 6-months or so. One of them happens to be this pretty cool MD-based unit, the CMT-M333NT! CMT-M333NT: The $30 kijiji Find: I got it locally off kijiji locally for very cheap--seller wanted $40 for it but I offered $30 and he said yes. Seller just needed to get rid of it and was second owner and the condition...well let's just say it had seen better days. But it's a rare find as far as I'm concerned and at the low price I figured I'd have a go with what was wrong with it. I'm not sure how I happened upon it, I was actually looking for some other stuff but saw it and snagged it. Seller mentioned in ad that the front "had a dent in it" which allegedly "looks like it might have been designed like that but it's actually bent"; also that the CD drawer would not close and he'd never tried CDs in it since it was broken like that when he bought it (second hand from someone else). Also said the tape deck he'd never tried, but no one really cares about that right? lol. The good part? The MD section functioned perfectly fine. Well it was a tiring drive downtown on a very hot day to get to this guy's place. The pictures of the unit on kijiji (which has terrible images btw--can't they fix that crap?) did *not* tell the entire story. The unit had seen better days, let's put it that way Though for $30 I wasn't expecting top notch condiditon. So the entire front panel was dented/*broken* inwards but miraculously it still worked, rotary encoder included. Clearly the CD drive tray was broken such that it looked fine but was just free sliding and not on the track/gear at all so CDs couldn't be loaded and the drive made some awful grinding noises in an attempt to work. The [top-mount] tape deck's door also warped so didn't stay down correctly (it's just latched with a push-button effect which only "caught" about 50% of the time). The MD section functioned fine though, as promised. The speakers also use proprietary little plugs and one was cut off and the speaker wire mangled and very poorly rigged back up. But they worked, and not even a dust cap pushed in, so that was also good news. I gave the guy the $30 and lugged the thing back down the street to my car (parking was also impossible on a hot end-of-summer day in Toronto's beaches area); headed to another kijiji buy (a Sony BD player) and then trekked home. The Restoration: At this point I'll stop and say I really wish I had taken "Before" pictures of this thing given the shape it was in and what it looks like now. All pictures you're going to see here are the "After" pictures as I didn't think about posting this until most of the work was done. To begin with, the unit was pretty bad overall, though functioning. I went to work on it once I got home, starting with a trusty screwdriver, lol... Front Panel: Overall it seemed like someone dropped the main unit on its face or something crashed into it. Guy that sold it claimed he bought it like that 2nd hand, many years ago, and only ever cared about the MD feature and never bothered with the tape or CD). But my goal here was to get it all working again. The plastic of the top panel was a bit warped and the finish on it badly, badly oxidised. The front panel (other than being completely broken) was a bit dirty, some of the buttons gunked up and to press some of them you really had to press as the board was bent behind them. Paint/finish was not bad but again this had definitely seen better days. Once I got it home and open I saw that was basically just pure luck the circuit board in the front panel did not break from whatever impact it sustained all those years ago. The board in the front panel was so badly bent I was actually quite shocked it remained intact not just after whatever happened to it but after many years of the stress of just being left like that--indeed no one had attempted to correct the physical problem! It was also a miracle the rotary encoder worked because it's main "mount" points (non-electrical but soldered in to ground) were basically broken right off the board--solder pads separated underneath. Well I was able to straighten it out and glue/epoxy the face back together where it had "dented" [broken] in. It actually came out quite nicely--it almost doesn't look like anything ever happened to it The unit was not scratched on the face but I cleaned the entire thing up quite well so overall the exterior looks very nice now which I'm pretty pleased with. I basically dismantled the entire front panel washed all the non-electrical/plastic parts, and put it back together. Polished and waxed it and looks nearly as good as new. Upon re-assembly I noticed the rotary encoder stopped working Doh! Ironically in straightening the board it cracked the solder pad of the encoder to the surface-mount capacitor inline with one of the contacts. Easy enough fix since the cap is right beside it--I just bridged it with a drop of solder, heh You can see right at the top of the volume knob there^ where the unit was broken originally. The entire part of the unit down that line to the disc tray was broken inward creating an "angled" front panel--which is why the guy said it looked like it "might have been designed like that if you didn't know". Anyway, fixed now! Also I *may* have installed the light guide for the light strip backwards, lol. I'm not sure, I will have to check the S/M over again to see. I think I had it the other way around to begin with when I first disassembled the panel but I'm not sure which is right now. Top Panel & Tape Deck: Meg's Ultimate Compound, Ultimate Polish, and NXT (car products) helped shape it up pretty well. The top panel being so badly oxidised looks 10x better now, though apart from getting a new panel it'll never be perfect. The top panel had a lot of warpage from what I can only attribute could have been one or two (or combination of) things. First the internal operating heat had warped it over time as the top acts as the vent for the amp; two, someone had left this thing in a window in the sun. With the oxidation the latter also makes sense. The tape deck, believe it or not, worked fine even with the warped door and the drive belt seems to be fine as well. I was able to fix the warped door pretty well enough to not have it pop open randomly. I used a heat gun to reshape it. It's an ABS top panel and door. Here's the thing about ABS, you can reshape it with heat but basically you heat it to a certain point and at that point it's almost like it becomes liquid. It really becomes a mush exactly at that point and it's also really easy to screw it up. When it's melty you can reshape it and after it cools in a few seconds it will retain that shape. I didn't want to push my luck on it too much so once I got the door good enough to hold down I called it a day. The top panel looks quite nice now though the tape door does still bend upwards on the one side. Because the tape holder only serves as an insertion mechanism and the tape still sits flat against the "floor" of the tape deck once you close the door, it doens't affect azimuth or operation at all. So it's really just cosmetic. I also properly cleaned and de-magged the heads and yes I "still actually have casettes somewhere" that I could test it out. Plays quite well, despite being utterly featureless as far as a full-logic deck goes (no Dolby, no CrO2/Metal tape detection OR selection, not even AMS). The Speakers: The speakers were in fairly good condition. The finish was a little scored up and dirty but the drivers were good. The speakers are made from wood and have pretty small 3.5" or 4" drivers. The tweeters are 1" polyprop but they're like super tweeters--the highs are quite in-your-face. As said the drivers were good and not even a dust cap push-in, which was surprising given the condition of the rest of the thing haha. Oddly the "veneer" pieces on where the speaker faceplate attaches to the back of the speaker, it's almost like they shrunk or were somehow replaced with ones from smaller speakers. But the colour is a match so I think that somehow they did actually shrink, exposing some wood surface on the sides of the speakers. Couldn't really do much there. One speaker actually had ball-point pen on the top writing some short number/letter combo like those codes you get on Steam when you log in from a different PC lol. Pretty ridiculous someone would write on a speaker with a pen but good news I was able to scrub that out, again by using some Meg's compound (though I suppose magic eraser would have worked too). The grilles are pretty good, a couple corners on one of them frayed/ripped, but nothing too big. One also has a very small spot where it almost looks like a mild bleach hit it but can't really fix that. Guy had cats I think so I washed the grilles in mild laundry detergent and then Febreezed them for good measure. Fixed the badly mangled wire, temporarily for now (as I'm not sure what length of speaker wire I'm going to use in the end), but the funny part is my temporary fix is miles better than what this guy had done as a full-time fix! He was smart enough to find terminal ends to at least hold into the speaker pins without the proprietary plugs, I'll give him that much. But he didn't even insulate them with tape in the event they might come together at some point and short out the amp! Then he had fixed the wire in two places (four wire mends for +/-) but he just twisted the wires together in 3 of 4 places, again without even tape to insulate! In a 4th place he used a small wire nut lol. No crimps, no tape but twisting and one wire nut--that oughtta do it! LMAO. All that said and done, treated all the surfaces as well as the cones and surrounds with 303 Aerospace protectant. The sound? Sounds exactly like it's supposed to but I'll touch on that part in the later review. The CD Section: The biggest challenge has been the CD section... First off the CD section is at the bottom. To get to this thing you have to dismantle the entire unit internally, except the power supply/amp section. The problem with the door was the cam (which holds in the gear to drive the door and additionally raises the pickup to the disc when closed) was broken off so the door would not stay on the gear/track at all. I searched and found the part was discontinued and "NLA" (no longer available) even from places that still listed it. At first I thought I was doomed to finding a broken/parts unit one of the few models Sony used the same part in (the rare unit itself, a few rare other CMT units, and literally two DVD-based HTIBs). But then as luck would have it I found the broken part of the cam elsewhere in the unit. Extremely lucky actually and I even found a *tiny* little "roller" ring that goes onto it, also inside the unit. That ring is really not necessary but I found that too, so that was nice. But how to get it back into one piece? I tried to super glue it and JB weld it to no avail--just broke instantly. But found that epoxy worked (though I had to try two kinds after breaking it again continiuning to troubleshoot/repair the thing). I restored the door operation function! I really had thought the spindle motor and pickup would be fine and I was close but not quite that lucky. The laser part is one of those rare ones where the spring part that assists the sled also serves as a dust cover for the lens when it's "parked". Well that thing was broken so I just cut it off (it's not necessary and though I taped it at first I found it was interfering with the disc still). At first I could get discs to read the TOC and display CD-Text info but playback was really spotty. It would play but then skip around like full tracks at a time and just continue reading at some other random place a track or two later in the disc. I figured it must be the rather stiff and rackety sled motor. Well this actually uses a common-type RF-300CH motor for the sled, which is really pretty cheap but strangely not easy to get because there's newer versions of these in wide use now so the old ones are all basically found as pulls and from private sellers or small shops selling on eBay, etc. I read up that these motors are commonly used also as spindle or disc tray motors and I found a close enough one in an old DVD-ROM drive--an RF-300FA variant which is higher torque and RPM. I went to work on dismantling the pickup assembly, desoldering both motors from their boards and doing the swap. I put the CD drive section back together and uh oh...it was even worse, now would not even spin the disc! Well duh, I had forgotten to re-solder one side of the spindle motor which I also had to desolder to get the other motor to shimmy out without breaking the pickup's circuit board. Reassembled the thing again and now it would spin but not at speed and only momentarily but stop. Damnit!!! So then I thought perhaps there was some "synergy" between the sled motor and now that it was moving faster than before there must be a problem. So now I go through all the time to put the old motor back in, just to see...but same thing! Then it hit me, when I reassmebled the pickup mechanism the springs that float it, I put them on the wrong side! This meant there was just too little pressure (the magnetic catch notwithstanding) to properly rotat the disc. Ugh what a nightmare. SO much time wasted! At least when I reassembled it I sprayed lubricant in the old sled motor and it freed it up quite nicely and it actually doesn't skip around anymore so maybe I should have just started with that lol. The CD section really took me a lot of hours of time, much of it wasted via my own stupidity...In the end I did not bother re-swapping to the newer sled motor, I just left it like that. End result? Still not perfect :| BUT, it does play CDs now! It has heavy clicking from the pickup itself (not from the audio other than the leaked noise from the pickup) on early tracks on a disc, which indicates error correction, but it loads, ejects, and plays! The good news is it is possible to get replacement lasers from China and after a lot more searching I found not only the full pickup assembly but also the entire drive mechanism (pickup assmebly + disc tray/loader) for not much more money than that. It goes $25 US for the laser assembly or $35-40 for the pickup assembly (w/laser, sled, spindle & board) or about $45 for the entire drive. These are not found as cheap as the $15-20 popular pickups found in mainstream CD players, but at least I found reasonably priced ones as opposed to the $150-200 part pricing on new ones in the US. To replace the CD drive it's obviously going to cost me about double what I paid for the unit itself, but hey them's the breaks. I'll have to wait a couple months before I even get the thing from China so I put it back together as is for now. I would NOT even think of doing a 4x CD->MD record on it as it is now haha. Not like I'd be using MDs anyway but again the goal here is to fully restore this thing functionally and to get it looking good cosmetically. Other notes...and pictures!: All in all I'd say for a $30 find I did very well. I'm really happy with the result but TBH I spent a lot of time over the past week on this thing, just getting it back to where it should be. Far more hours of labour put into it than what I had paid for it. One might say I didn't really fix much mechanically other than the CD drive (which still doesn't even work 100% well), but trust me guys had you seen this thing in the beginning, you'd see the world of difference. I actually messaged the seller saying I was restoring it but they never replied--oh well guess they weren't interested. If anyone is wondering why I bothered with this much effort, well I dunno that's kind of what I do sometimes haha. Plus I'm planning on getting out all my old MD units and placing them in this cabinet I have kind of as a display of what MD "once was" Because that cabinet has a missing glass shelf I have to replace that first though, then add some LED lighting (which is oh so cheap/easy these days) and I think I'll have a nice little showcase in the end, with the HCD-M333NT unit as the centre piece. IMO it's a beauty of a unit and I'm glad I found it on the off chance while browsing kijiji. This unit actually has a lot of great and interesting features I must say, including it's ability to simply function as a USB D/A for PC use. I'll touch on those in the next post which will be the review though. Some other interesting points about this unit are that the IR remote system is very unlike other Sony units as in it breaks the Sonly standard where mini-sytems only work with mini-system commands, boomboxes only work with boombox commands, and home components only work with home-component commands. In odd fashion this thing responds not only to mini system commands but also to separate commands from component CD player IR, and MD deck IR as well. I haven't actually tried tape deck commands but it stands to reason they'd work too. Also this unit has a "motherboard" on it but it almost serves only as an input switcher, controls centre, and display provider. There's only a couple ICs on it and they're not really what you'd call main ICs. Instead the MD section serves almost as if it were the main controller of the unit--it really is an MD-centric unit. I also found that directly beside the TORX optical input receiver there's a place for a TOTX optical emitter. I searched the paths in the service manual but they're completely undocumented despite the screening on the board for the cap and component. When I went through the circuit diagrams I found via the pinout for the MD system controller, this should definitely be connected to digital output pin and may well simply require a TOTX emitter and a small cap to make function. It's not entirely clear though if this will only provide digital output from the MD deck section or if it will also output CD audio from there. Because all input carries to the MD board first (as said it's basically the true motherboard), I'm not sure if it will output CD while in CD mode or not. It's not really something I'm going to use but I'm going to order some Toslink emitters nonetheless and hook one up here next time I open it, and see what happens. Shot of back panel I/O and the temp speaker wire fix for one of the speakers. The space between the USB and the Digital Input are where the Digital Output transmitter goes on the main board inside. It's too bad the unit doesn't have analog line output as well, to hook up a small sub or something--there's the phones jack but that's not the same. There is some kind of "RGL" connector inside the unit which the S/M remarks is "not used in this unit" which could well be analog line out but I haven't looked into it yet. Anyway I know this is crazy long, but comments are welcome...even if they are to say, "dude you wasted a lot of time on this old-technology piece of junk!"
  2. The problem with rubber bands is they'll eventually just snap. Hopefully yours will last as long as possible but rubber bands can "band aid" a belt fix in a pinch (like say you needed to eject a disc stuck inside) but they really aren't great for the long term. Typically speaking, most manufacturers use certain belt sizes/types for a wide array of applications, so it's possible you can find a belt on eBay, etc. that will work. Sometimes it's hard to track down what you're looking for as they just have belts for certain models--you basically have to find a cross-reference for that part# and then try searching more popular models for the belt. Anyway, given you seem to have had the one in the JB940 last a couple years, that's not bad at all! I'm actually quite surprised it's lasted that long but then again an MD's eject mechanism is pretty light duty given the small size of the discs.
  3. Seller of the JA3ES has terrible feedback though. Also JA3ES was the least "ES" of all the ES MD decks. I like to think of it as ES-lite, lol.
  4. Interesting that some Hi-MD units charge from USB. I only have a DH10P (my only Hi-MD unit) which is 2nd gen, and it certainly doesn't charge over USB!
  5. The encryption keys only have to do with playback and not with actually reading the disc. If the encryption keys are not up to date the player will read the disc fine and attempt to play it but upon playback it will tell you the disc cannot be played until the player is updated. If the player won't read the disc at all, that's a pickup or spindle or other mechanical problem with the player.
  6. Wow, well that should end cheap with that feedback score--bit of a risk there. PayPal may protect but big pain there and still may end up losing the money in some cases. Now that it's posted here, it'll probably drive the price up too lol. Also shipping for American buyers is pretty steep...
  7. All Hi-MD that can record or "download", can be powered for playback/record/download from USB IIRC. However they cannot charge a battery via USB. Since the NH600D also has no DC-in jack it cannot charge a battery at all. The NH600 (no D) does have DC-in but it never came with a rechargeable AA I don't think. So I'm not sure if it has the charge circuit or not given I've never used one--someone with one would have to verify. Though it should be the "cheapest Hi-MD", I agree with the sentiments above that people ask way too much for them on eBay. NH600Ds are typically listed at $150+ which ridiculous. 600Ds were sold at retail for about $100 at the end of the MD era, selling a used one now for more money, is jokes. You could easily just bid on/buy a second-gen Hi-MD unit instead, for similar money...or less!
  8. ^There are rechargeable AAs you know, lol. Meaning AAs can actually be more ecologically correct given a cylindrical cell has more capacity (within the same chemistry) and longer lifespan compared to a prismatic (rectangular) rechargeable. Also rechargeable NiMH AAs are much better for modern devices* than throw-away batteries as they hold up against higher drains, whereas alkaline and other throw-away AAs suck at this**. This is not significant for MD after the Rx00 generation since they were not really high drain a devices except when recording, but NiMH AA is better overall in any MD unit using AA, IMO. As for holding a charge, Eneloops (and similar) have been doing this reasonably fine for many years now so it's not really an issue. These type of NiMH batteries will hold charge for a year or more and still be at 85%+ capacity. *Of course most modern devices have long abandoned AAs anyway, in favour of internal Li-Ion/Li-Ion-Poly cells and USB recharging. **The only exception to throw-away AAs and high drain are Energizer 1.5V Lithium AAs which have a discharge curve similar to a rechargeable when loaded up, but they are one-use/discardable. As for what I think personally? I still kinda like the units that use gumsticks better. Perhaps because there was no battery bulge, perhaps because they were typically the high-end units. Perhaps a bit of both. Also, I didn't realise this was a zombie thread, LOL. 2007!
  9. Any 5-6V regulated supply or switching adapter capable of 500mA or more and have an appropriate plug, should work; a transformer adapter (the old "brick" ones) with the same rating as well but will probably float 8-9V unloaded so if using a transformer adapter you could probably use a "4.5V" adapter fine as well. If you give it too much voltage (within reason) the unit will flash "Hi DC In" and refuse to work, so it's not a huge deal if you overvolt it a little--it has built in protection to some degree. USB has okay voltage however it is current limited. The theoretical limit (before you trip protection or blow a fuse on the mobo) is 500mA on most USB ports. Therefore USB-charging devices typically do not draw more than ~384mA from a standard USB port (they only try to draw more when connected to USB-AC adapters). Since the NH1 (and all MD units for that matter) was before USB charging was common, you'd be charging with the unit just thinking it's connected to an appropriate AC adapter which may overload the port (the unit will just try to draw whatever current it needs at 5V). So, it may not charge correctly on a USB port given the lower voltage and current limit (which may damage your mobo if exceeded). Personally I would play it safe and just find a genuine 6V Sony switching adapter on eBay or something--I'm sure they can't cost more than $15.
  10. The RH10 is not the same as an M200, it's the same as an M100. I'm pretty sure PCM transfers work on any HiMD unit though no? The only thing that makes the RH1 special (in this regard) is that it can upload "classic" (MD-SP) recordings to the computer.
  11. There's also another guy (in Germany I think it was?) that used a cylindrical Li-Ion cell, along with a spring (to make it longer) and cardboard (to hold it in place), as a replacement successfully. This method does not require the unit be disassembled. Since cylindrical cells have higher capacity for similar volume, the guy stated that the capacity is the same. However I don't really trust the Chinese capacity ratings he's probably going by; I'd have to know what the standard capacity is for that particular size but I never looked into it. Nonetheless I think he reported similar run times. I also found a listing for a BK062265 Li-Ion prismatic cell on eBay (which can also be found on google). "BK062265" refers to a generic part code used for nearly all Li-Ion/Li-Ion-Poly cells in which the numbers merely describe the dimensions. Therefore 062265 refers to 65 x 22 x 6 mm. Unfortunately when I measured the LIB-902 it comes out to 67 x 18-19* x 5 mm, so I'm not sure if it would work. *LIB-902 is "keyed" so that part of it is slightly taller than the rest of the battery. **Edit, scratch what I said before, the key actually does prevent it from being inserted the wrong way, not sure why I didn't get that before; it doesn't prevent it from being inserted upside down, however. So the one I found is about 2mm too short meaning the use of a spring may still be required or perhaps just using some tin foil. I'm not sure if the entire ends of the "BK062265" are entirely contacts or if it's just a small portion (can't find pics of the ends), so foil may actually be a good idea. Now the width of the battery is 1mm too large but if one broke off the latch at the end of the unit (where the battery door clips in) it should fit as within the unit there is enough space otherwise. Now this may sound like a bad idea but the truth is on the F70 that latch doesn't do that much for the battery door because it is also held in by the base of the latch (when you press it in) and, perhaps more importantly, the lid of the entire unit holds the door in place when both are closed. In fact the lid can't be closed until the battery door is closed. Also since the length of the replacement is 2mm shorter, this may not even be required as it my just "snug in" before the portion of plastic that forms that latch bit. (You have to have one in your hands to get what I'm talking about here.) The only thing I can think would prevent such a cell from fitting is the height. **Edit: Because the key prevents it from being inserted wrong, one would have to remove or cut the part at the end of the battery housing in order to fit a higher battery. It's too hard to tell whether 3mm would prevent the door from closing, but I think it might close being a tight fit. Would have to spend about $10 on the battery to try, but it's probably worth a shot. Since I have a working LIB-902 (*knock on wood*) I'm not in a real rush, but someone desparate for a battery may want to try. Okay 2nd edit: I tried putting a toothpick (which is about 2mm) over top the LIB-902 and closing the door--no dice. So a 062265 will NOT fit However I'm thinking there has to be some generic Li-Ion prismatic size that should. Might take a little searching...
  12. I think that the deduction Sony has parts and refurb RH1 units stocked is about right. Even if you look up some of the parts, you can see "part requested"/"part supplied" listings that show things like "internal only" when decoded. I'm guessing they have few parts though, so they don't sell them to the public and only use them for warranty and pay-for repairs in their factory service centres. That said OP probably doesn't even need parts just a new calibration done if the service menu values were erased. I do find it hard to believe someone would get into that mode and erase data by accident though. LOL @ the table thing though I'm guessing OP's first language is not English.
  13. Ah I see, so thanks to jonathanpotato for the spreadsheet then! What I'd love to find is some cheap LCX-4Es because I have two E900s and one E700 with failing pickups (all were bought that way on the cheap back in the day). Also I had another E700 that was fully working that eventually totally failed (don't have that one anymore though). LCX-4E pickup is a piece of crap, let me tell you, LOL. But it'd be nice to get my hands on a few working ones to fix these units--esp. my blue E900.
  14. Very cool. Now the question is...how/where can we get some of these?
  15. Ehh like "Another MD Fanatic" above said, it's almost certainly not worth it to repair. The MS701/MS702 always had this problem--if you can find all the old stuff on the intarwebs about "Sharp UTOC error" you'll see what I mean. Allegedly the later units with the "MK" suffix on the box/model label were improved but who knows by how much. I'm pretty sure any MS701/702 will fail eventually in the same fashion. Might as well just buy another MD unit off eBay, etc. and hopefully not a Sharp from this generation! Then you can relegate the Sharp to playback only duty though you might want to look into permanently disconnecting the OWH because I'm pretty sure those units were also known to randomly erase discs, but I can't rememeber now.
  16. Only thing I can offer here is that the Li-Ion batteries of "yesterday" were built a little more stringently, to higher quality standards, and used high quality materials and manufacturing. You have to remember that this was back when most portable MD recorders were still running off 3.6V drive (Li-Ion voltage) and NiMH units were not yet commonplace. In fact the MZ-R55 which would come out that same year was the first one to use NiMH gumstick IIRC. But it had horrible battery life as I doubt it was engineered as a 1.2/1.5V drive unit but instead was adapted from a 3.6V design. Battery life on the R55 was essentially cut in half from the R50 and it wouldn't be until the next generation (the R90/91) where battery life became good. (This was also the start of the power cycling instead of keeping the disc spinning indefinitely, IIRC.) Prismatics (gumsticks, rectangular batteries) have never been a match for their cylindrical counterparts either. Not in capacity and not in longevity (cycle life) and durability (environmental/physical). However they met the size criteria cylindrical cells could not. The unfortunate part about NiMH prismatics is they were even poorer than LiIon prismatics. Even the well manufactured ones weren't anything spectacular and the many poorly made ones (China-made, knock offs, counterfeits) made the situation even worse. However at least they are still made and available, albeit from 3rd party (and mainly China made) companies. It's a good thing the LIB-902s have good life though, because it's impossible to find those anymore as they simply aren't made. Unlike cylindrical Li-Ion batts they aren't universal or standardised either so there's no real way to replace it at all! I actually have one sitting in front of me right now. I think when I stored it, it could do at most about 70% it's original rated capacity, which it probably still has since it was stored at low temp. Still, if used again, this battery will probably eventually die and then what? Well it's pretty tough finding Li-Ion prismatics. You're definitely never finding this exact battery again though there are similar cells made. Can't paste links to this forum for some reason but if you search google for "BK062265 Li Ion" you'll find something like that might work as a replacement for the LIB-902.
  17. Strangely I can't do anything when making posts. Like can't use Quote/Multiquote, nor can I even cut/paste into a post text window (like the one I'm typing in now). Can't paste links or anything else for that matter. CTRL+V does nothing, and the little paste buttons in the editor don't work either. I can't even use the image button to insert an image as the dialog pops up but when I paste in the link the OK button is still greyed out...and so is the cancel button! I can hit the "X" in the corner to close the dialog and then it asks me if I'm sure and I say yes, but the dialog remains open! LOL, wtf? I'm using IE 11, even tried compatibility mode but it stays the same. Tried the quick message post thing as well as going to the advanced/full page editor to no avail. What gives? Do these 'features work' for everyone else? I've yet to try another PC (I have lots so I guess I will try that next).
  18. Ahh okay PC to speaker. But that is changing the total USB mode of the system, correct? When you do that, the unit shows up as an audio device in Windows (typically using Windows built-in drivers), either as "Speakers", "USB DAC", or "Audio Sink"--depending on version of Windows and exact device type. If this is the case the unit is acting as if it itself were a USB "soundcard", which is how you get the output from the PC. Again this isn't really an audio "input" in that sense either, but I see what you mean. In this case you would need any device that acts as a host that can output to a USB sound device of that type. Obviously a Windows PC can do it, possibly a Mac, and possibly some standalone devices. However when in "PC to speaker" mode, can you record? If so, I believe all you would need to do is input whatever you wanted to the PC, with the Z05 as the output device. You'd need to set monitoring output to the "speakers" (in this case the Z05) and you should be all set. If you don't have line or digital inputs on your computer or laptop, then you can get any USB device that can do that for a PC--there are many out there.
  19. Unfortunately what you're saying would not work out of the box as you say--you'd have to hack SS/NetMD to a degree that no one else has ever been able to. I wouldn't get my hopes up. Keep in mind you may also be misinterpreting how NetMD works. Transfers from the computer are not audio transfers, they are file transfers. The PC encodes whatever it is to ATRAC3 and then sends it to the NetMD device to write to disc; and, these files are DRM-protected as well. Therefore it's not really just as easy as getting the "USB input to become active" because it's not really an "input" per se. It's a USB connection that allows DRM-protected file transfers. You'll have to make it so SS encodes and transfers whatever input signal you have and the uploads the data to the MD unit. Realistically you can already do this though, can't you? Just record whatever it is to .wav using an input device on your PC (whether it be the PC's existing soundcard/chip or an external device) and then convert to ATRAC3 and send to the MD unit. If you actually want a standard audio input though, I think you'll have a lot easier time doing something slightly different... The recording function from CD-->MD internally more than likely uses S/PDIF [TTL]. Provided that signal is carried in the unit between two places (and not all done within the same IC) from CD output to the ATRAC IC, you can probably disconnect that line and then fool the unit into thinking it's recording from CD while you feed it an S/PDIF signal from somewhere else. In order to retain original functionality of recording from CDs you'd have to build some kind of switch or auto circuit to switch between CD and external source recording. This of course requires some degree of skill working with electronics, soldering, and surface mount component stuff. Now to record an analog source you'd either need to tap into the analog L/R into the ATRAC IC (if there is a tuner on this you can record from for example) or you'd need an A/D converter and just use the digital input you made, above. Remember if you use an A/D you'd probably need to convert the "external" S/PDIF to TTL S/PDIF (0.5V to 5V) which is not hard to do given the rest of the project. Or if you only need to record analog you could just do the analog part and essentially disable tuner recording--that would probably be easiest. However to be totally honest, you'd do better just to get another unit on the cheap you can record from.
  20. Yeah stupid TrPROT! I guess if it is ignored on a JE640, decks definitely never got the "feature" until they had NetMD which is odd considering how many years prior portables had it! Even more odd than M-Crew enforces restrictions that the decks themselves do not. Looks like Sony had totally different groups working on these products--the guys that designed the decks didn't bother enforcing TrPROT but the M-Crew guys knew the decks could read/recognise the flag and utilised it properly. Very, very inconsistent application of this flag it seems. Pretty cool that you have one of those Onkyo decks--those are rare!
  21. Hate to break it to you but Sony will never make another MD anything except perhaps blanks and accessories, at least not in the near future. Sony is in enough [financial] "trouble" as it is, they're not going to go and put resources into making a new unit for a dead format that was a niche format even in its heyday. Yes they have returned to profit now, but it's for the first time in like 5+ years. They're still making structural changes--they've sold off their VAIO business and will make further changes in the near future (Bravia TVs will be spun off into a separately-branded division for example). Only thing they're really making big $$$ on now is PS4 and that's probably going to be their main focus for the coming years while they continue to axe or restructure losing or less profitable parts of the company. Most MD manufacturing and development ceased years ago, with nearly all of it ending in 2011. Sony only announced the total end of shipping MD units about a year ago, a decision it's not going to just reverse all of a sudden. it would cost them more money to make 1000 MD units than they'd ever get back from them, unless they charged an exorbitant price for a cheaply made unit. Sony is simply not in a position to fool around with MD anymore. TBH from a business point of view it makes absolutely no sense for them to do that, especially with the company's current position. I'd imagine any exec that tried to green-light any kind of MD production today, would be fired tomorrow or get lynched by shareholders lol. Perhaps in the future they may have some kind of anniversary model but I doubt it given the anniversary models are already done with (N10,E10) and Sony never revived any other formats after they died (they've never made a Beta anything since 2002 and like MD it had died in practical terms a few years prior to that). Anyway my advice would be to look into just getting a nice second hand unit (and really you can even find NIB/NOS units from time to time). For HiMD you're kinda screwed in that there was only that Onkyo one (actually might have been two models?) and I can't imagine those being had for less than several hundred. Instead I would look for a JB780 or JB980 if you want a fairly nice deck with NetMD. Obviously JA333ES prices will be in the sky and no NetMD there anyway. JE480s can probably be had for cheap but looks like you're trying to find a better deck than that. Definitely don't keep your hopes up of Sony producing any new MD products anytime soon.
  22. Do the quote buttons actually work on the forum? I tried both "Quote" and "MultiQuote" and neither seems to work. Funny part is when I go to post something else I get a pop up saying I have quotes stored I haven't used but how exactly do I use them? Anyway yeah I've seen both the Vapex and Powerstream on eBay though the Powerstream seem like they might be fresher and are cheap as they are sold in bulk--no money wasted on the packaging and stuff of the Vapex ones. I guess Sony stopped making/selling these now? You can't even get the counterfeit ones on eBay anymore, lol. GP are also long gone it looks like, along with Sanyo Slims There are the no-name China ones as well, but I wouldn't trust them to have anymore than 900-1000mAh regardless of marking but you'd have to analyse one to tell. I actually have quite a few gumsticks of different types, dunno what condition they are in nowadays but I just took a few I had stored out of refrigeration* which should be good still, but I'm interested now in making an adapter I can connect to my MH-C9000 as someone else did earlier in the thread. Unfortunately I don't really have any chargers I want to bust up to accomplish this. I think however I can do it by modifying one of the battery carrying cases. Hopefully I can design something that doesn't add too much resistance between the battery and the charger *Note that I would suggest if anyone is storing NiMH or NiCd batteries over long periods for units you don't use often, to discharge the batteries first and keep them at low temperatures--either refrigerated or in the freezer. This will prevent them from breaking down on their own which will happen much more quickly at room temp and higher and at higher states of charge. Li-Ion can be stored at low temps as well but should be discharged only to about 30-40% capacity instead of totally discharged. Also never store a Li-Ion at full charge, especially at room temp or higher as cell degradation is quite bad like this. Yes they will not lose charge like NiMH but they will lose usable capacity relatively quickly, esp. when stored over 20 Celsius.
  23. The idea that MD-SP hardware might not read MDLP data is an interesting one, though I don't think it's necessarily true. If we look at our friend PhillipeC's spreadsheet we can see that indeed the pickups are slightly different between a JA333ES and a JA20ES. The former uses a KMS-260A while the latter uses a KMS-260B. However I believe these are interchangeable anyway, though I'm not 100% sure. Best example I can remember though is the story of a guy that modified his MDX-66XLP to have optical output. As people might remember the MDX-65 had optical out (this was used mainly for Sony car DSP units back then) and was SP only while the MDX-66XLP was the later model, nearly exactly the same except the chassis colour and the fact that it could play MDLP discs. The unit also lacked the optical out the 65 had. These units also have a similar optical pickup dissimilarity--the 65 uses a KMS-241A while the 66XLP uses a KMS-241C. I remember talking to the guy (email) about how he went about accomplishing the optical output on the 66XLP. I assumed he had used the easiest route and gotten the optical out components from the 65 and simply put them in the otherwise identical-chassis 66XLP. Funny enough he said he had never thought of that, LOL! Instead of doing this (which would have been much easier), he did something else. He had access to surface mount soldering gear so he actually changed the ICs in the 65 to any that were different in the 66XLP! Instead of making a 66XLP have optical out, he made a 65 be able to read/play MDLP instead! He never mentioned having to change pickups so if we go by that, it should be the case that non-LP pickups can indeed read LP data. The second evidence to support that would be the fact that non-MDLP units will play LP discs, but they just ignore the audio data. They play the discs as if they were mono (IIRC?) and the time counter still increases; they also get the track name header "LP2" or "LP4" displayed along with the track name. However LP tracks have a bit set so the decks know not to try to decode the data as audio. So I'm thinking that a KMS-260A should have no problem reading an LP disc in LP hardware, in place of a 260B. I've never heard of this being done before but I'm at least pretty sure they are interchangeable. Perhaps someone like Phillipe could chime in and confirm?
  24. Nice finds. Indeed what the others have said is spot on. RH1s are insanely expensive to acquire, for several reasons. The main one of which? It was the only unit that allowed you to upload SP recordings to a PC. It was also never produced in very big numbers to begin with and has long gone out of production (along with everything else MD). Though I get your enthusiasm and nostalgia over MD, I can't see why anyone would want to go back to using it today as a main source of music playback. Flash memory is so darn cheap and there's so many other options out there to record/store/play music. For example even a low-end cellphone will have more storage than several HiMD discs, nevermind regular MD discs. The average phone will have like 20 times the storage of one HiMD disc not to mention mostly free of the draconian restrictions and sluggish speed of NetMD. Don't get me wrong I still have a relative wealth of MD gear (some of which I'm re-discovering now that I've been doing some cleaning up at the house), but I dunno I'd never think of using any of it seriously, lol. I even have two NW-HD3s in a cabinet which have been unused for probably 6-7 years or so. Yeah they were 20GB devices and at the time very small for that capacity as well. They were great back then. But today? LOL. Anyway you did get some nice finds esp. a new in box deck for that price Personally I wouldn't be putting the effort into trying to use MD as a main format anymore, but if it's just for nostalgia I get that as I'm firing up some of my old MD stuff right now myself Either way though, hope you have fun with the new gear If you get tripped up by SonicStage and start swearing and cursing and stuff though, just remember that's all part of the fun of MD
  • Create New...