Jump to content

Search the Community

Showing results for tags 'mz-nh1'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Miscellaneous
    • Announcements
    • Classifieds
    • Corporate
    • The Loft
  • Categories
    • Audio
    • Cameras & Camcorders
    • Minidisc
    • Mobile
    • PlayStation
    • Product Reviews/Pictorials
    • TV
    • Vaio
    • Software
  • Essential Hi-MD info/FAQ's.

Categories

  • Programs
  • Service Manuals
    • Minidisc Decks
    • Bookshelf
    • MD Portables
    • MD CD Combo decks
    • Hi MD Service Manuals
    • NW Service Manual
    • Other Service
  • Drivers
  • User manuals
    • MD Portables User manuals
    • HiMD Portables User Manuals
    • MD Decks User manuals
    • MD CD Combo decks User manuals
    • Bookshelf User manuals
    • Network Walkman User manuals
    • Other User
  • Headunits
  • Receivers
  • CD and DVD players

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


Website URL


Skype


Location


Interests


PlayStation Network ID


Sony Products I Own


ATRAC Devices


Headphones


Amplification


Minidisc units


Microphone Equipment

Found 4 results

  1. Hi, I'm new on this forurm and I have a problem when my MZ-NH1 is charging. The Charging lamp does not work anymore. Has anyone ever encountered this problem?
  2. After Sphig's success with finding a method of replacing worn out batteries for the MZ-N10, MZ-E10 and MZ-1, I thought I'd look into a solution for those of us who have units that run on the almost impossible to replace LIP-4WM using the same inexpensive 3.7 volt battery sourced from eBay. The link for the battery is at the bottom of this post. Please only attempt this if you are confident in what you are doing and be sure not to short circuit either the old or new battery as this can be dangerous. I cannot be held responsible for damage to either you or your valuable MD equipment. For this you will need to sacrifice your old dead LIP-4WM as we will be using parts from it. 1. Carefully remove the sticker from the old battery. 2. Once the sticker is removed you will notice that the opposite face of the battery from the contacts is black and shiny. This is another sticker and you should also carefully remove this. It is very sticky so you may need to use the edge of a blade to lift the edge of it. 3. After removing the second sticker, you should see the silver metal casing of the battery itself. The battery is glued to the plastic casing and will need to be very carefully revoved without damaging the plastic back battery housing. I did this by gently flexing the end of the plastic casing furthest from the contacts away from the battery slightly and then sliding the end of a wide plastic cable tie in between the battery and casing to separate them. 4. Using a pair of scissors you should now be able to cut through the two metal tabs connecting the battery to the PCB with the battery contacts. Cut these as close to the battery as possible to leave as much of the metal as you can attacked to the circuit board in the platic casing. 5. You should now have the plastic back battery housing with just the contact PCB and its small plastic cover. Your new battery can now be placed in the plastic housing and secured using piece of very thin double sided tape or glue. 6. The wires from your new battery should now be soldered onto the tabs that the old battery was attached to, making sure that you get the polarity correct. You can see the correct way to connect the wires in the photos below (the negative connection is next to the diagonal cut off corner of the casing). 7. I then used a piece of regular sticky tape to go over the area where the wires and connections are just to keep it slightly more secure and less prone to accidental short circuiting of the new battery. I used thin sticky tape rather than electrical tape because there is very little room in the battery compartments of these MiniDisc units and electrical tape is a little too thick and causes fitting problems. 8. Finally I added a piece of sticky tape to the underside of the end of the battery housing that doesn't have the contacts and folded the end of it over to make a battery removal tab as shown in the photos, as the newly fitted battery is a very cosy fit (certainly in the NH1 I tested it with), and this gives you something to hold on to when removing the battery from the unit. You should now be good to go. As you can see from my pictures, my MZ-NH1 is now happily running on its new battery and I see no reason why this shouldn't be a success in any other MD unit that uses the LIP-4WM although I don't have anything other than the NH1 to test this for myself. The NH1 operates exactly as it should and charges fine from its charging cradle. I hope this helps any of you who, like me, are having problems with batteries that have seen better days. Good luck:) http://www.ebay.com/itm/181291308343?_trksid=p2055119.m1438.l2649&ssPageName=STRK%3AMEBIDX%3AIT
  3. Since I found the excellent tutorial on this forum to add drivers to my Win7 PC for NetMD I've a renewed interest in my minidisc equipment. Using Sonic Stage I've successfuly transferred some Cds to MD which I can play on my HiFi via my MDS-S40 deck. However I've noticed that the cable covering at the MD plug on the USB data cable I use to connect my PC and the MZ-NH1 is broken. My fear is that this makes the wires going into the plug vulnerable. I've not been able to source a replacement cable so far. Does the cable have a code number or does anything else use the same cable? If I can connect via the optical cable does that transfer album and track data like the USB cable does? Thanks for any advice.
  4. So it's finally happened; both of my LIP-4WM gumstick batteries have died and will no longer hold charge. I see many of the LIP-4WM for sale on ebay and random places, but to my knowledge these are all original run Sony brand and are surely pretty old (bad news for lithium-ion batteries). Does anyone make replacements or equivalents for this battery? I dont care if its some tiny specialty place that charges $100 a pop, just would like to snag a couple of new ones
×
×
  • Create New...